Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM A635/A635M-22
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
Translate name
STANDARD published on 1.9.2022
The information about the standard:
Designation standards: ASTM A635/A635M-22
Publication date standards: 1.9.2022
SKU: NS-1086038
The number of pages: 15
Approximate weight : 45 g (0.10 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM A635/A635M-22 :
This specification covers the general requirements for hot-rolled, heavy-thickness, and high-strength low-alloy with improved formability sheet and strip coils. These coils are normally produced from rimmed, capped, or semi-killed steel. Steels may be produced as ingot-cast or strand-cast. Cast or heat analysis shall be made to determine the conformance with the requirements. For steels other than non-killed (capped or rimmed), product analysis may be made. The chemical analysis shall conform to the specified amounts of carbon, manganese, phosphorus, sulfur, silicon, and copper. Steels may or may not be subjected to tension test requirement. Specimen preparation and test methods are discussed. The mechanical property requirements, number of specimens, test locations, and specimen orientation shall be in accordance with the applicable product specification. Tolerances for the dimensions of sheet and strip coils are specified.
Keywords:
carbon, commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel,, ICS Number Code 77.140.50 (Flat steel products and semi-products)
Additional information
| 1. Scope | ||||||||||||||||||||||||||
|
1.1?This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils. 1.2?It applies to Specifications A414/A414M, A424/A424M, A1018/A1018M, and A1031/A1031M. 1.3?This material is available only in coils described as follows:
Note 1:?The changes in width limits with the publication of
A635/A635M 06a result in a
change in tensile testing direction for material from 0.180 in.
[4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in.
[1200 mm] wide, as that material is now covered by Specification
A568/A568M 06a. The purchaser
is advised to discuss this change with the supplier.
1.4?In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.5?For the purposes of determining conformance with this and the appropriate product specifications referenced in 1.2, measured values, calculated values, and observed values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5.1?Ordered values, identified in tables, specified such as over 30 through 48, or 30 exclusive to 48 inclusive, covers all ordered values specified as 30.1, 30.01, 30.001, etc., up to and including 48.000 etc., but does not cover ordered values specified as 30.000 etc. or less, nor does it cover ordered values specified as 48.1, 48.01, 48.001, etc., in accordance with the absolute method of Practice E29. 1.6?Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the M specification is used. Note 2:?The term weight is used when inch-pound units are
the standard. However, under SI, the preferred term is mass.
1.7?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8?This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable M specification designation (SI units), the material shall be furnished to inch-pound units. 1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||
|
||||||||||||||||||||||||||
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
