ASTM C564-20a

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings (Includes all amendments and changes 5/13/2020).

Translate name

STANDARD published on 1.5.2020

Language
Format	PDF - Immediate download - 61.00 USD PDF + redline - Immediate - 73.20 USD Print design - 61.00 USD Print + redline - 73.20 USD
Availability	IN STOCK
Price	61.00 USD excl. VAT
61.00 USD

The information about the standard:

Designation standards: ASTM C564-20a
Publication date standards: 1.5.2020
SKU: NS-993138
The number of pages: 4
Approximate weight : 12 g (0.03 lbs)
Country: American technical standard
Category: Technical standards ASTM

Send to a colleague

Query

The category - similar standards:

Seals for pipe and hose assemblies

Annotation of standard text ASTM C564-20a :

This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. Gaskets shall be made of a properly vulcanized virgin rubber as the sole elastomer with no scrap or reclaim. Gaskets shall conform to the required physical properties such as hardness, elongation, tensile strength, tear strength and compression. The gasket material shall be tested for effects of heat aging. They shall be tested for weight increase due to water absorption and shall also be tested for volume decrease due to oil absorption. Gasket material shall be tested for ozone resistance.

Keywords:

cast iron, fittings, gaskets, pipe, rubber,, ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)

Additional information

1. Scope

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings.

1.2 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D395-18	Standard Test Methods for Rubber Property´Compression Set
D1149-18	Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment
CISPI 310	Specification for couplings for use in connection with hubless cast iron soil pipe and fittings for sanitary and storm drain, waste, and vent piping applications Available from Cast Iron Soil Pipe Institute (CISPI), http://www.cispi.org.
RMA	Class 3 Dimensional Tolerances, RMA Manual Available from Association for Rubber Products Manufacturers (ARPM), 7321 Shadeland Station Way, Suite 285, Indianapolis, IN 46256, http://www.arpminc.org.
D3677-10(2023)	Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D1415-18	Standard Test Method for Rubber Property´International Hardness
D573-04(2019)	Standard Test Method for Rubber´Deterioration in an Air Oven
A644-17	Standard Terminology Relating to Iron Castings
C1277-20	Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
D471-16a(2021)	Standard Test Method for Rubber Property—Effect of Liquids (Includes all amendments and changes 6/25/2021).
D624-00(2020)	Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

We recommend:

Updating of laws

Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.

Here you can customize your cookie settings according to your preferences.

We need your consent to use the individual data so that you can see information about your interests, among other things.