ASTM D3855-84(2010)..
ASTM D3896-07(2011)..
ASTM D3958-06(2011)..
ASTM D4004-06(2012)..
ASTM D4026-06(2012)..
ASTM D412-06a(2013)..
Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM D2229-10(2014)
Standard Test Method for Adhesion Between Steel Tire Cords and Rubber (Withdrawn 2023)
Automatically translated name:
Standard Test Method for Adhesion Between Steel Tire Cords and Rubber
STANDARD published on 15.5.2014
The information about the standard:
Designation standards: ASTM D2229-10(2014)
Note: WITHDRAWN
Publication date standards: 15.5.2014
SKU: NS-19684
The number of pages: 7
Approximate weight : 21 g (0.05 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM D2229-10(2014) :
Keywords:
adhesion, rubber, steel, tire cord, ICS Number Code 83.060 (Rubber)
Additional information
| Significance and Use | ||||||||||||||
|
5.1 This test method is considered satisfactory for the acceptance testing of commercial shipments of steel tire cord because current estimates of between-laboratory precision for single materials are considered acceptable and the method has been used extensively in the trade for acceptance testing. 5.1.1 If there are differences or practical significances between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogenous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.2 The mold described in this test method is primarily designed for quality acceptance testing for steel cord where the sample size for each cord is 4 or a multiple thereof, but any mold/cavity combination which will provide the required test block dimensions (Figs. 1 and 2) is acceptable. FIG. 1 Definition of Test Block
Dimensions
TOLERANCES
All dimensions ±0.2 Angular ±2° Except where noted 5.3 Appendix X1 contains suggested ranges
of environmental conditions for aging tests.
5.4 The property measured by this test method indicates whether the adhesion of the steel cord to the rubber is greater than the cohesion of the rubber, that is, complete rubber coverage of the steel cord, or less than the cohesion of the rubber, that is, lack of rubber coverage. |
||||||||||||||
| 1. Scope | ||||||||||||||
|
1.1 This test method covers the determination of the force required to pull a steel cord from a block of vulcanized rubber. 1.2 Although designed primarily for steel cord, this test method may be applied with modifications to wire used in rubber products. 1.3 This test method can also be used for evaluating rubber compound performance with respect to adhesion to steel cord. 1.4 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
Similar standards:
Historical
1.5.2010
Historical
1.11.2011
Historical
1.11.2011
Historical
1.5.2012
Historical
1.5.2012
Historical
1.1.2013
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
