ASTM D2683-20

Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

Translate name

STANDARD published on 1.11.2020

Language
Format	PDF - Immediate download - 69.00 USD PDF + redline - Immediate - 82.80 USD Print design - 69.00 USD Print + redline - 82.80 USD
Availability	IN STOCK
Price	69.00 USD excl. VAT
69.00 USD

The information about the standard:

Designation standards: ASTM D2683-20
Publication date standards: 1.11.2020
SKU: NS-1010367
The number of pages: 6
Approximate weight : 18 g (0.04 lbs)
Country: American technical standard
Category: Technical standards ASTM

Send to a colleague

Query

The category - similar standards:

Plastics fittings

Annotation of standard text ASTM D2683-20 :

This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or machined from extruded stock. Special fittings such as transition fittings and tapping teets shall be assembled and fabricated. Conditioning, dimensions, short-term rupture test, and sustained pressure test shall be performed to conform with the requirements specified.

Keywords:

ICS Number Code 23.040.45 (Plastic fittings)

Additional information

1. Scope

1.1 This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe as specified by Specifications D3035 and D2513. Requirements for materials, workmanship, dimensions, and pressure performance are included. Where applicable in this specification, “ pipe” shall mean “pipe and tubing.”

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

F412-23	Standard Terminology Relating to Plastic Piping Systems
D3035-22	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
PPI TR-3	Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe7
PPI TR-4	HDB/SDB/PDB/MRS Listed Materials, PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2513-20	Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D618-21	Standard Practice for Conditioning Plastics for Testing
MIL-STD-129	Marking for Shipment and Storage
Fed. Std. No. 123	Marking for Shipment (Civil Agencies) DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA 19111-5094 http://quicksearch.dla.mil/
D2657-07(2023)	Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

We recommend:

Technical standards updating

Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.

Would you like to know more? Look at this page.

Here you can customize your cookie settings according to your preferences.

We need your consent to use the individual data so that you can see information about your interests, among other things.