We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
Standard Test Method for Pile Fabric Abrasion
Translate name
STANDARD published on 1.7.2020
Designation standards: ASTM D4685/D4685M-15(2020)
Publication date standards: 1.7.2020
SKU: NS-999976
The number of pages: 6
Approximate weight : 18 g (0.04 lbs)
Country: American technical standard
Category: Technical standards ASTM
Keywords:
The sole source of supply of the apparatus known to the committee at this time is Taber Industries, North Tonawanda, NY. If you are aware of alternative suppliers, please provide this information to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.,, ICS Number Code 59.080.30 (Textile fabrics)
Adjunct to D4685 Standard Test Method for Pile Fabric Abrasion
Selected format:Significance and Use | ||||||||||||||||
5.1 This test method is considered satisfactory for quality control testing and commercial shipment acceptance. 5.1.1 In case of a dispute arising from differences in reported test results when using this test method, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take test specimens that are from the lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias. 5.2 Finishes and changes in fabric surfaces may exert a large effect on pile retention of corduroy. Therefore, it may be desirable to test before as well as after laundering or drycleaning, or both. 5.3 The separate testing of specimens on the face and back of the fabric is important in this test method since the pile pull-out may be due to abrasive action on either the face or back. With many pile fabrics, specifically corduroy constructions, pile retention properties are worse when abraded on the back. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method covers the determination of the abrasion of pile fabrics when the loss of pile tuffs occur, sometimes called pile retention or pile pull out. It includes two procedures: 1.1.1 Procedure A—The “Heavy Duty” procedure describes the test option for fabrics over 240 g/m2 (7 oz/yd2) or fabrics which should meet heavy duty end-use conditions of wear. 1.1.2 Procedure B—The “Light Duty” procedure describes the test option for fabrics under 240 g/m2 (7 oz/yd2) or fabrics which should meet light duty end-use conditions of wear. 1.2 The test method is intended for both regular, ribless woven corduroy or other woven pile fabric constructions. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.
Latest update: 2024-12-22 (Number of items: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.