Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM D7793-13
Standard Specification for Insulated Vinyl Siding
STANDARD published on 1.9.2013
The information about the standard:
Designation standards: ASTM D7793-13
Note: WITHDRAWN
Publication date standards: 1.9.2013
SKU: NS-39122
The number of pages: 11
Approximate weight : 33 g (0.07 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Plastics and rubber insulating materialsThermoplastic materials
Annotation of standard text ASTM D7793-13 :
Keywords:
insulated siding, insulated vinyl siding, plastic building products, plastic weatherability, recycled plastic, rigid PVC siding, specification, vinyl siding, ICS Number Code 29.035.20 (Plastic and rubber insulating materials), 83.080.20 (Thermoplastic materials)
Additional information
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification establishes requirements for insulated vinyl siding, which is vinyl siding with integral foam plastic insulating material, where the vinyl siding is manufactured from rigid PVC compound. Compliance with this standard requires insulated vinyl siding to demonstrate a thermal insulation value of R-2.0 or greater. Other performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, thermal distortion resistance, and windload resistance. Methods of indicating compliance with this specification are also provided. 1.2 Insulated vinyl siding shall be
tested with the insulation material in place or removed, as
specified in the applicable requirement or test method.
1.3 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 1.4 Insulated vinyl siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
|
|
Standard Practice for Packaging/Packing of Plastics
|
|
Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products (Includes all amendments and changes 8/21/2020).
|
|
Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
|
|
Standard Test Method for Windload Resistance of Rigid Plastic Siding
|
|
Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
|
|
Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
|
|
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
|
|
Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions
|
|
Standard Practice for Outdoor Weathering of Plastics
|
|
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
|
|
Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
|
|
Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer
|
|
Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture
|
|
Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation
|
|
Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods
|
|
Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions
|
|
Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
|
|
Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board (Includes all amendments and changes 10/3/2023).
|
|
Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
|
|
Standard Practice for Conditioning Plastics for Testing
|
|
Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
|
|
Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
|
AC05
|
Acceptance Criteria for Sandwich Panel Adhesives
|
ISO/IECGuide 65
|
|
|
Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
|
16 CFR Part 460
|
Labeling and Advertising of Home Insulation
|
|
Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
