ASTM F2881-11

Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

STANDARD published on 1.3.2011

Language
Format	PDF - Immediate download - 83.00 USD Print design - 83.00 USD
Availability	IN STOCK
Price	83.00 USD excl. VAT
83.00 USD

The information about the standard:

Designation standards: ASTM F2881-11
Note: WITHDRAWN
Publication date standards: 1.3.2011
SKU: NS-54663
The number of pages: 8
Approximate weight : 24 g (0.05 lbs)
Country: American technical standard
Category: Technical standards ASTM

Send to a colleague

Query

Annotation of standard text ASTM F2881-11 :

Keywords:

fittings, interior liner, PP, pipe, polypropylene, profile wall, storm sewer, ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)

Additional information

1. Scope

1.1 This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for nonpressure storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig. 1).

1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2990-17	Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3895-19	Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
D4101-24	Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
D6992-16(2023)	Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
LRFD, Section 12	AASHTO LRFD Bridge Design Specifications Section 12 Buried Structures and Tunnel Liners

Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
D4389/D4389M-23	Standard Specification for Finished Glass Fabrics Woven From Rovings
D638-22	Standard Test Method for Tensile Properties of Plastics
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
MIL-STD-129	Marking for Shipment and Storage
D256-23e1	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
D618-21	Standard Practice for Conditioning Plastics for Testing

We recommend:

Technical standards updating

Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.

Would you like to know more? Look at this page.

Here you can customize your cookie settings according to your preferences.

We need your consent to use the individual data so that you can see information about your interests, among other things.