ASTM C1681-14
ASTM C564-14
ASTM C877M-02(2009)..
ASTM D1869-95(2010)..
ASTM D6396-99(2012)..
ASTM F1336-07
Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM F2946-12
Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes
STANDARD published on 1.8.2012
The information about the standard:
Designation standards: ASTM F2946-12
Note: WITHDRAWN
Publication date standards: 1.8.2012
SKU: NS-54770
The number of pages: 4
Approximate weight : 12 g (0.03 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM F2946-12 :
Keywords:
elastomeric seal, rubber gasket, service connection, sewer tap, watertight seal, ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)
Additional information
| 1. Scope | ||||||||||||||||||||||||||||
|
1.1 This specification covers the minimum performance and material requirements for a three piece tee connector for connection between plastic pipe and insitu pipes, manholes and wastewater structures in sanitary and storm sewer applications. 1.1.1 The three piece seal system consists of a 4 through 30-in. PVC (polyvinyl chloride) hub pipe, an elastomeric seal (gasket) and a mechanical band (Fig. 1). The system is installed in either a bored or cast hole opening in the host pipe or structure to a specific dimension that corresponds to the combined diameter of the PVC pipe outside diameter/tolerance and the elastomeric seal thickness. FIG. 1 Three-Piece Sealing System
(Connector)
1.2 These tee connectors are designed to provide a non-pressure (gravity flow) watertight connection between the incoming pipe and an insitu pipe or manhole/structure to the limits defined in this standard. 1.3 The following precautionary
caveat pertains only to the test methods portion, Section
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
|
|
Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes all amendments and changes 10/8/2021).
|
|
Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
|
|
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
|
|
Standard Terminology Relating to Concrete Pipe and Related Products
|
|
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
|
Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
|
C900
|
Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. Through 12 in. (100 mm Through 300 mm), for Water Transmission and Distribution
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
|
|
Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air (Includes all amendments and changes 5/13/2020).
|
|
Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals |
Similar standards:
Historical
1.6.2014
Historical
1.5.2014
Historical
1.10.2009
Historical
1.6.2010
Historical
1.10.2012
Historical
1.5.2007
We recommend:
Updating of laws
Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.
