ASTM D2996-01(2007)e..
ASTM D2997-01(2007)e..
ASTM D3034-14
ASTM D3035-14a
ASTM D3139-98(2011)..
ASTM D3212-07(2013)..
Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM F2969-12
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe
STANDARD published on 1.8.2012
The information about the standard:
Designation standards: ASTM F2969-12
Note: WITHDRAWN
Publication date standards: 1.8.2012
SKU: NS-54797
The number of pages: 5
Approximate weight : 15 g (0.03 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM F2969-12 :
Keywords:
ABS, HDB, plastic pipe, pressure piping, SDR, ICS Number Code 23.040.20 (Plastic pipes)
Additional information
| 1. Scope | ||||||||||||||||||||
|
1.1 This specification covers acrylonitrile-butadiene-styrene (ABS) IPS dimensioned pressure pipe produced by single extrusion in standard thermoplastic pipe dimension ratios and pressure rated for water (see Appendix X1). Included are criteria for classifying ABS plastic pipe materials and ABS plastic pipe, a system of nomenclature for ABS plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, and extrusion quality. Methods of marking are also given. 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids, which are chemically compatible with the piping materials. Consult with the manufacturer and local building codes before use in other applications. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. 1.3 Pipe meeting the requirements of
this standard is not compatible with DWV fittings. The ABS pipe
covered in this standard is intended for pressure service and it
shall be joined to pressure fittings. Non-pressure fittings, such
as DWV fittings from any material (ABS, PVC, CPVC, etc.) are not
acceptable for pressure applications.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.6 The following safety hazards
caveat pertains only to the test method portion, Section
Standard Practice for Conditioning
Plastics for Testing Standard Test Method for Time-to-Failure
of Plastic Pipe Under Constant Internal Pressure Standard Test Method for Resistance to
Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and
Fittings Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) MIL-STD-129 Marking for Shipment and Storage Standard Terminology Relating to Plastic
Piping Systems Standard Test Method for Determining
Dimensions of Thermoplastic Pipe and Fittings Standard Test Method for Obtaining
Hydrostatic Design Basis for Thermoplastic Pipe Materials or
Pressure Design Basis for Thermoplastic Pipe Products Standard Classification System and Basis
for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS)
Materials for Pipe and Fittings |
Similar standards:
Historical
1.3.2007
Historical
15.3.2007
Historical
1.3.2014
Historical
1.8.2014
Historical
1.2.2011
Historical
1.2.2013
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
