Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM F959-13
Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
STANDARD published on 1.3.2013
The information about the standard:
Designation standards: ASTM F959-13
Note: WITHDRAWN
Publication date standards: 1.3.2013
SKU: NS-57076
The number of pages: 5
Approximate weight : 15 g (0.03 lbs)
Country: American technical standard
Category: Technical standards ASTM
Annotation of standard text ASTM F959-13 :
Keywords:
compressible-washer-type, direct tension indicators, DTI, indicators, ICS Number Code 21.060.01 (Fasteners in general)
Additional information
| 1. Scope | ||||||||||||||||||||||||||||||||
|
1.1 This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a structural bolt. 1.2 Four types of direct tension indicators in nominal diameter sizes 1/2 through 11/2 in. are covered: 1.2.1 Type 325—direct tension indicators for use with Specification A325 Type 1 bolts or F or F1852 assemblies. 1.2.2 Type 325–3—direct tension indicators for use with Specification A325 Type 3 or F1852 Type 3 assemblies. 1.2.3 Type 490—direct tension indicators for use with Specification A490 Type 1 bolts or F2280 assemblies. 1.2.4 Type 490–3—direct tension indicators for use with Specification A490 Type 3 F2280 Type 3 assemblies. 1.3 Direct tension indicators are intended for installation under either a bolt head or a hardened washer. (See Research Council on Structural Connections: Specification for Structural Joints Using ASTM A325 or A490 Bolts.) 1.4 This specification provides for furnishing Types 325–3 and 490–3 to a Chemical Composition Requirement or a Corrosion Resistance Index (CRI) at the suppliers option. 1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 The following
precautionary statement pertains only to the test method portions,
Section 12 and Appendix X1 of this specification:
Standard Specification for Structural
Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength
(Metric) (Withdrawn 2016) Specification for Structural Joints Using
HighStrength Bolts Standard Guide for Estimating the
Atmospheric Corrosion Resistance of Low-Alloy Steels Standard Specification for “Twist Off”
Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel,
Heat Treated, 150 ksi Minimum Tensile Strength (Withdrawn 2016) Standard Specification for “Twist Off”
Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel,
Heat Treated, 120/105 ksi Minimum Tensile Strength (Withdrawn
2016) Standard Terminology for F16 Mechanical
Fasteners Standard Practice for Fastener Sampling
for Specified Mechanical Properties and Performance Inspection Standard Test Methods for Determining the
Mechanical Properties of Externally and Internally Threaded
Fasteners, Washers, Direct Tension Indicators, and Rivets ASMEB18.2.6 Fasteners for Use in Structural
Applications Standard Specification for Structural
Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile
Strength Standard Specification for Structural
Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
(Withdrawn 2016) Standard Specification for High-Strength
Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints
(Metric) Standard Specification for Coatings of
Zinc Mechanically Deposited on Iron and Steel Standard Specification for Hardened Steel
Washers Standard Specification for Hardened Steel
Washers [Metric] (Withdrawn 2016) |
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
