We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
Standard Practice for Use of a Radiochromic Optical Waveguide Dosimetry System
Translate name
STANDARD published on 1.11.2020
Designation standards: ASTM/ISO 51310-22
Publication date standards: 1.11.2020
SKU: NS-1054848
The number of pages: 6
Approximate weight : 18 g (0.04 lbs)
Country: American technical standard
Category: Technical standards ASTM
Keywords:
absorbed dose, dosimetry, electron beams, gamma radiation, ionizing radiation, optical waveguide dosimetry, quality control, radiation processing, ICS 17.240,, ICS Number Code 17.240 (Radiation measurements)
Significance and Use |
4.1?The radiochromic optical waveguide dosimetry system provides a means of measuring absorbed dose in materials. Under the influence of ionizing radiation such as photons, chemical reactions take place in the radiochromic optical waveguide creating and/or modifying optical absorbance bands in the visible region of the spectrum. Optical response is determined at selected wavelengths using the equations in 3.1.4. Examples of appropriate wavelengths for the analysis for specific dosimetry systems are provided by their manufacturers and in Refs (4.2?These dosimetry systems commonly are applied in the industrial radiation processing of a variety of products, for example, the sterilization of medical devices and radiation processing of foods (Note 1:?For additional information on dosimetry systems used in radiation processing, see ICRU Report 80. |
1. Scope |
1.1?This is a practice for using a radiochromic optical waveguide dosimetry system to measure absorbed dose in materials irradiated by photons and high energy electrons in terms of absorbed dose to water. The radiochromic optical waveguide dosimetry system is generally used as a routine dosimetry system. 1.2?The optical waveguide dosimeter is classified as a Type II dosimeter on the basis of the complex effect of influence quantities (see ISO/ASTM Practice 52628). 1.3?This document is one of a set of standards that provides recommendations for properly implementing dosimetry in radiation processing, and describes a means of achieving compliance with the requirements of ISO/ASTM 52628 for an optical waveguide dosimetry system. It is intended to be read in conjunction with ISO/ASTM Practice 52628. 1.4?This practice applies to radiochromic optical waveguide dosimeters that can be used within part or all of the specified ranges as follows: 1.4.1?The absorbed dose range is from 1 Gy to 20 000 Gy. 1.4.2?The absorbed dose rate is from 0.001 Gy/s to 1000 Gy/s. 1.4.3?The radiation photon energy range is from 1 MeV to 10 MeV. 1.4.4?The radiation electron energy range is from 3 MeV to 25 MeV. 1.4.5?The irradiation temperature range is from 78 ?C to +60 ?C. 1.5?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
Latest update: 2024-08-30 (Number of items: 2 345 304)
© Copyright 2024 NORMSERVIS s.r.o.