We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
Standard Practice for Separation and Concentration of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration with Solid Phase Microextraction (SPME) (Withdrawn 2024) (Includes all amendments And changes 4/4/2024).
Automatically translated name:
Standard Practice for Separation and Concentration of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration with Solid Phase Microextraction (SPME)
STANDARD published on 1.9.2015
Designation standards: ASTM E2154-15a
Note: WITHDRAWN
Publication date standards: 1.9.2015
SKU: NS-615840
The number of pages: 3
Approximate weight : 9 g (0.02 lbs)
Country: American technical standard
Category: Technical standards ASTM
Keywords:
fire debris samples, passive headspace concentration, solid phase microextraction (SPME),, ICS Number Code 27.060.10 (Liquid and solid fuel burners)
Significance and Use | ||||||||||||
4.1 This practice is suited ideally for screening samples for the presence, relative concentration, and potential class of ignitable liquid residues in fire debris. 4.2 This is a very sensitive separation procedure, capable of isolating small quantities of ignitable liquid residues from a sample, that is, a 0.1 μL spike of gasoline on a cellulose wipe inside of a 1-gal can is detectable. 4.3 Actual recovery will vary, depending on several factors, including adsorption temperature, container size, competition from the sample matrix, ignitable liquid class and relative ignitable liquid concentration. 4.4 Because this separation takes place in a closed container, the sample remains in approximately the same condition in which it was submitted. Repeat and interlaboratory analyses, therefore, may be possible. Since the extraction is nonexhaustive, the technique permits reanalysis of samples. 4.5 This practice is intended for use in conjunction with other extraction techniques described in Practices E1386, E1388, E1412, and E1413. 4.6 The extract is consumed in the analysis. If a more permanent extract is desired, one of the separation practices described in Practices E1386, E1412, or E1413 should be used. |
||||||||||||
1. Scope | ||||||||||||
1.1 This practice describes the procedure for removing small quantities of ignitable liquid residues from samples of fire debris. An adsorbent material is used to extract the residue from the static headspace above the sample. Then, analytes are thermally desorbed in the injection port of the gas chromatograph (GC). 1.2 This practice is best suited for screening fire debris samples to assess relative ignitable liquid concentration and for extracting ignitable liquid from aqueous samples. 1.3 This practice is suitable for extracting ignitable liquid residues when a high level of sensitivity is required due to a very low concentration of ignitable liquid residues in the sample. 1.3.1 Unlike other methods of separation and concentration, this method recovers a minimal amount of the ignitable residues present in the evidence, leaving residues that are suitable for subsequent resampling. 1.4 Alternate separation and concentration procedures are listed in Section 2. 1.5 This standard cannot replace knowledge, skill, or ability acquired through appropriate education, training, and experience and should be used in conjunction with sound professional judgment. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Historical
1.10.2010
Historical
1.10.2014
Historical
15.12.2014
Historical
1.7.2013
Historical
1.5.2014
Historical
1.10.2014
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
Latest update: 2024-12-22 (Number of items: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.